Spa Heat Pumps

Pool spa heat pumps are stand-alone units that utilize a technology that relies on a compressor and a fan to extract heat from the surrounding air. Afterward, the technology enables heat transfer to the spa water. Swim spa heat pumps are more efficient than heating, thereby reducing electrical energy consumption. Energy consumption reduces by 75% compared to that of the electric heater element. SPRSUN air source heat pump spa heaters are the most energy efficient way to heat your spa and swimming pool by saving up to 75% energy.



Spa Heat Pumps



  • How to Clean A Pool Heat Pump?

    A pool heat pump has three parts frequented by dirt, the heat exchanger, the fan blades, and the region inside. You have to turn off the power supply and unscrew the heat exchanger. When open, apply a degreaser to the exchanger using a soft brush. Give it time to loosen the soot and wash it using a garden hose. On the inside, ensure you clean the leaves and the muck, which accumulate with time on the pool heat pump’s bottom. A wet vac will suffice for the task. Lastly, with the fan blades, use a piece of clothing and a cleanser to clean the tips. The metal gills enclosing the fan should also be blown by a blower to remove accumulated dust.

  • Can A Heat Pump Cool a Pool?

    Whether a heat pump will cool your pool or not will usually depend on the model. There are heat pumps that have heating and cooling modes conjoined in the same device. They use a reversing valve or even inverter technology. As such, they can defrost and keep heating even when temperatures are extremely quite low. Such heat pumps are able to extract heat energy from the surroundings if a heating need arises. Also, the process can be reversed by triggering a cooling sequence in which they pull more heat from the pool’s water and then transfer it into the air.

  • How Much Power Does A Pool Heat Pump Use?

    In general, heat pumps draw heat or cold from exterior outdoor air, ground, or water and transfer it indoors for warming or cooling. They are somewhat less expensive from an operational expense point of view. A heat pump graded as 100,000BTU will averagely consume around 5,000 watts, or 5KW every hour. Using it four hours a day will consume 20KW—a kilowatt of electricity costs anywhere between $.13 to $.16cents per hour. The rates will vary depending on the utility provider. Therefore, a heat pump running for an hour will need approximately $.80 and $3.2 power charge in a day.
  • What Size Heat Pump Do I Need for My Pool?

    For starters, a small pool (10000-20000 liters) a 13KWh heat pump will do the job. For medium pools (20000-40000 liters) a 15-18 KWh will be sufficient. For large pools (40000-60000 liters), a 21-23 KWh heat pump is ideal. These values, however, vary depending on the temperature of your region. To narrow down on the exact heat pump you need, you require 0.00116 KWh of power to heat one liter. Knowing your pool size and the degrees you want to raise your pool temperature by, you can accurately determine the heat pump you need using the formula given below. It is simply pool size in liters × 0.0016 KWh × degrees you wish to raise your pool water by. At SPURSUN, we have a wide range of quality pool heat pump to meet your need.

  • How Long Does a Pool Heat Pump Last?

    While electric, gas, and solar heaters have a short life span, a pool heat pump can outlast them all. The typical life span of a pool heat pump is about ten years or more. However, several key factors play a role in the life expectancy of a pool heat pump. You can extend the lifespan of your pool heat pump up to fifteen years or more if you are willing to put in a little effort. And it all starts with proper installation, care, and maintenance. Overall, a pool heat pump is a good investment that might supersede your expectations. SPRSUN heat pumps present all the qualities needed to last longer and work efficiently.

  • How to Install A Pool Heat Pump?

    The location of the heat pump will, in a great way, affect how efficiently your heat pump will work. Ensure that your heat pump is close enough to your filter and not more than 25 feet away from the pool. If you place it away from the pool, the heated water will cool down before getting to the pool. It is also vital that you ensure that there are no obstructions near the heat pump. Give it at least 30 inches or more of clearance all around it. Doing so will ensure that there is sufficient air that gets into the heat pump. Once you install it, you can run it to see if it efficiently heats the pool. 
  • How Does A Pool Heat Pump Work?

    Swimming pool water passes through the filter when the pool is being used to get rid of any dirt or debris. It is during this process that the water for a heated pool gets warmed up. What happens is, the heating pump takes in warm air from the outside and turns it into warm gas. As the warm gas passes through the pump's coils, it increases the heat in the compressor. As the water passes through this compressor, the energy is transferred into the water. The now warmed water returns to the pool and helps heat the water in the pool as well. The process repeats itself until the pool water is warm enough.



  • Can Air Source Heat Pump Heat a Whole House?


    Probably you have been once deluded about a ductless heat pump requiring air handlers, or "heads," in each room. That's not the case, however. Dependent on the home's structural envelopes & air movement, a single head unit will potentially heat a 1500 sq. ft house. However, old buildings with furthe Read More

  • What Is a Heat Pump Boiler?


    Heat pump boilers heating pumps that integrate both a boiler and an air source of a ground source heat pump. This equipment works conjointly. But the gas or oil boiler only supplements the heat pump when the heat generated is inadequate. Thus, the unit automatically switches between the heat pump an Read More

  • What Are the Disadvantages of Air to Water Heat Pumps?


    Heat pumps use a compressor and a revolving system of liquid refrigerant. This transfers heat from one location to the other. Warmth is taken from pools or water sources and then circulated indoors.These pumps have several benefits for your house. They consume less energy as they do not use electric Read More

  • How Does a Split Heat Pump Work?


    A split-system heat pump is a technology that transfers heat from one location to another using a network of pipes, vents, and other components. It functions similarly to a standard central heating system. Instead of a single boiler, the system transfers heat from the outside unit to the inside unit Read More


A Professional Heat Pump Manufacturer Since 1999
No.15 Tangxi Road, Yinsha lndustrial Park, Xintang, Zengcheng District, Guangzhou, 511338, China


TEL: 0086-20-82181867
PHONE: 0086-18933985223
SKYPE: sprsun.sprsun